Thursday, May 27, 2010

Whimsy Lane (EZ Dresden Ruler Tutorial)

Good Morning!
I've been promising a 'Tutorial' on how to use the EZ Dresden Ruler for those of you who have seen me at the shows, so here goes!
(The following quilt was pieced and quilted by Marla McDermott of Kanab Utah)
  
Cut strips 2 1/2" wide (or use a Jelly Roll)
Using your EZ Dresden Ruler place the ruler straight on the fabric from 0 - 2 1/2". 
Using your rotary cutter slice your first set of blades.
Turn the ruler the exact opposite way and slice your next set of blades.
Continue to the end of fabric.


 
Fold blades right side together and sew across the widest portion with a 1/4" seam. 
Chain stitch several through the machine. Clip apart.
Turn inside out and using a blade turner poke out your point as best as you can being careful not to poke a hole through it.


Press. Your blades will look like this when they are done.  
To make the full flowers alternate your lights and darks paying attention to values and scales.
 
Center of Flower:
After cutting out your template for either the full flower, quarter or half, place it on top of some  iron on stabilizer which has the sticky side face down on top of the right side of the fabric for center piece.  Cut out circle (or half circle, quarter circle):

Sew a scant 1/4" seam around circle. Clip edges. Put a small slit in the stabilizer at back to turn the unit inside out. Make edges as smooth as possible. I run my blade turner all around the seam edge of the circle.  Do not press until it is on top of flower and ready to be applied to quilt top. Otherwise you will have it sticking to your ironing board.

 
Top stitchthe  flower petals on following your quarter inch foot on your machine. Find a decorative stitch to topstitch on the flower center. (It is hard to make a perfect circle. If you use a straight stitch to sew on the flower center all of your imperfections will show. I use the #19 stitch on my Bernina 125)
For Quarter Fan Blade Unit covers you can either finger press the cover 1/8" down, or use a circle like above and cut it into quarters OR: in the picture to the right, you can take the plastic template you made (as long as it is the NO MELT mylar) and adjust it where it is about 1/8" down from the top and use the plastic as a guide and iron it over it.

I like to use some spray starch at the top to help it stay folded down before stitching it on. When making the Quarter Fan Blade units, you stitch the fan blade cover on as close as you can to the edge.
I hope this helps!!

5 comments:

  1. Nice tutorial- love that pattern too! I usually use those same methods but I hadn't done the 1/4 circle before... I will have to look for no melt mylar! I will actually need to do that right now on a quilt I'm working on! Thanks a bunch!

    ReplyDelete
  2. Hi! Thanks a lot for your visit to my blog and your kind comments.=) I don't really think what I do is that impressive, I've just covered quite a few styles in the 8 years I've been stitching. Most of the work is other people's designs though.

    I am thinking of doing some of my own for sale at some point in the future, but I've no immediate plans for it just yet. We shall see!! I say that a lot!!

    All the best, Elizabeth=)

    ReplyDelete
  3. The Scrappy Apple yard has been promising a Tutorial on how to use the EZ Dresden Ruler. This all based upon the Mylar but it is very nice.

    ReplyDelete
  4. I visited your booth today at the Lincoln Mall in Freeport Illinois. I loved all your quilts and really enjoyed our chats. I can't wait to try the Mylar Hexagon's and the Dresden Ruler..thanks again for your beautiful quilts!

    ReplyDelete
  5. Grеetings from Idaho! I'm bored to tears at work so I decided to browse your blog on my iphone during lunch break. I enjoy the knowledge you provide here and can't
    wаit to take a lоok when Ӏ get hοme.

    I'm surprised at how fast your blog loaded on my cell phone .. I'm not even uѕing WIFI, just 3G .
    . Anуhow, wonԁегful site!

    Visit my web раge :: just click for source

    ReplyDelete